manualshive.com logo in svg

Waygate Technologies Krautkramer USM 10, Operating Manual

Share
Download
Waygate Technologies Krautkramer USM 10 Operating Manual Download Page 158

5  Operation

DAC

158

Rev. - (09/2021)

Krautkrämer USM 100

Automatic variation of the measuring point in TOF 
mode

An echo amplitude evaluation is normally carried out at 
the echo peak of the signal under examination because 
this is the only way of ensuring that the displayed echo 
amplitude and the sound path (projection distance, 
depth position) always belong to the highest echo in the 
gate.

Note

The instrument checks the measuring point 
setting in TOF mode before processing any 
reference amplitudes. If 

Peak

 is not set as 

measuring point, the instrument will automat-
ically switch to 

Peak

. In this case, a note is 

displayed at the bottom edge of the display 
screen.

Summary of Contents for Krautkramer USM 10



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands