manualshive.com logo in svg

Waygate Technologies Krautkramer USM 10, Operating Manual

Share
Download
Waygate Technologies Krautkramer USM 10 Operating Manual Download Page 139

Evaluation

5  Operation

Krautkrämer USM 100

Rev. - (09/2021)

139

Eval Mode

You must choose the evaluation mode before setting 
the following parameters.

dbRef Mode

This parameter is only visible when 

dB REF 

has been 

selected in 

Eval Mode

.

You can switch this function on or off.

Gate A Start

This is the same function as in the function group 

 

Gates

 (see page 127).

Eval Source

This parameter is only visible when 

DAC

, 

JISDAC

 or 

CNDAC

 has been selected in 

Eval Mode

.

You can choose between the A-scan and the envelope 
curve as basis for the probe angle calculation.

Eval Points Source

This parameter is only visible when 

DAC

, 

JISDAC

 or 

CNDAC

 has been selected in 

Eval Mode

.

For creating and editing the DAC curve points you have 
two options:

●

DAC Table

, the DAC table is defined with the soft-

ware 

Mentor Create

●

Custom

, you can record the DAC points with the in-

strument

The software 

Mentor Create

 is described in a separate 

manual.

Define Points

This parameter is only visible when 

DAC

, 

JISDAC

 or 

CNDAC

 has been selected in 

Eval Mode

.

You must set the number of points to be recorded.

Summary of Contents for Krautkramer USM 10



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands