Volvo 2016 XC60 Owner'S Manual Download Page 81

Page: 81 / 398

03 Instruments and controls

}}

Option/accessory, for more information, see Introduction.

Removing the remote key

The remote key can be removed from the

ignition slot by pulling it out.

Related information

•

Ignition modes (p. 79)

Ignition modes

The vehicle's ignition has 3 modes:

, and

that can be used without starting the engine.

The following table shows examples of which

functions are available in the respective

modes.

NOTE

To access ignition modes

without

starting the engine, the brake pedal must

not

be depressed.

Mode Function

The odometer, clock and tem-

perature gauge are illuminated.

Power seats* can be adjusted

and the infotainment system can

be used for a limited time (to min-

imize battery drain, see the Sen-

sus Infotainment Supplement).

The laminated panoramic roof,

power windows,12-volt sockets

in the passenger compartment,

navigation system*, climate sys-

tem blower, windshield wipers

can be used.

The headlights/taillights illumi-

nate. Warning/indicator lights illu-

minate for 5 seconds. Other sys-

tems are activated. However, the

heated seats* and heated rear

window function can only be acti-

vated when the engine is running.

Mode II should only be used for

very short periods to help avoid

draining the battery.

Ignition modes

Ignition mode 0

–

The vehicle is unlocked.

Summary of Contents for 2016 XC60














































































































































































































































































































































































































Search results

Summary of Contents for 2016 XC60

Reviews:

Related manuals for 2016 XC60

Brands by name

Popular brands

Volvo 2016 XC60, Owner'S Manual

Search results

Summary of Contents for 2016 XC60

Reviews:

Related manuals for 2016 XC60

Brands by name

Popular brands