Volvo 2016 XC60 Owner'S Manual Download Page 295

Page: 295 / 398

09 Wheels and tires

}}

Option/accessory, for more information, see Introduction.

293

Location of jack*, towing eyelet

and tools*

Changing a wheel

1. Apply the parking brake and put the gear

selector in

2. Take out the jack*, lug wrench*, the tool

for removing the plastic covers on the

wheel nuts, the towing eyelet and the

wheel cover removal tool (certain models

only) stowed under the floor of the cargo

area.

Tool for removing the plastic covers on the wheel

nuts

Remove the wheel cover (where applica-

ble) using the removal tool or remove the

wheel cover by hand.

4. Block the wheels that are on the ground

with wooden blocks or large stones.

Lug wrench and towing eyelet

5. Screw the towing eyelet into the lug

wrench as shown in the illustration.

CAUTION

The towing eyelet must be screwed into

the lug wrench as far as possible.

The towing eyelet may be partially concealed under the rear edge of the cargo area. See the illustration Towing eyelet (p. 285) for its location.

Summary of Contents for 2016 XC60














































































































































































































































































































































































































Search results

Summary of Contents for 2016 XC60

Reviews:

Related manuals for 2016 XC60

Brands by name

Popular brands

Volvo 2016 XC60, Owner'S Manual

Search results

Summary of Contents for 2016 XC60

Reviews:

Related manuals for 2016 XC60

Brands by name

Popular brands