Volvo 2016 XC60 Owner'S Manual Download Page 52

Page: 52 / 398

02 Safety

G023270

Positioning the seat belt through the infant seat

WARNING

•

An infant seat must be in the rear-facing

position only.

•

The infant seat should not be positioned

behind the driver's seat unless there is

adequate space for safe installation.

WARNING

A child seat should never be used in the

front passenger seat of any vehicle with a

front passenger airbag – not even if the

"Passenger airbag off" symbol near the

rear-view mirror is illuminated (on vehicles

equipped with Occupant Weight Sensor). If

the severity of an accident were to cause

the airbag to inflate, this could lead to seri-

ous injury or death to a child seated in this

position.

3. Fasten the seat belt by inserting the latch

plate into the buckle (lock) until a distinct

click is audible.

G023271

Fasten the seat belt

Pull out the shoulder section of the seat belt

4. Pull the shoulder section of the seat belt

out as far as possible to activate the

belt's automatic locking function.

Summary of Contents for 2016 XC60














































































































































































































































































































































































































Search results

Summary of Contents for 2016 XC60

Reviews:

Related manuals for 2016 XC60

Brands by name

Popular brands

Volvo 2016 XC60, Owner'S Manual

Search results

Summary of Contents for 2016 XC60

Reviews:

Related manuals for 2016 XC60

Brands by name

Popular brands