Volvo 2016 XC60 Owner'S Manual Download Page 383

Page: 383 / 398

11 Specifications

Option/accessory, for more information, see Introduction.

381

Battery specifications

If the battery is replaced, replace it with a bat-

tery of the same cold start capacity as the

original (see the decal on the battery).

General information

WARNING

PROPOSITION 65 WARNING!

Battery posts, terminals, and related

accessories contain lead and lead com-

pounds, chemicals known to the state of

California to cause cancer and reproduc-

tive harm. Wash hands after handling.

12 volt system with a voltage-regulated alter-

nator. Single pole system in which the chas-

sis and engine block are used as conductors.

The negative terminal is connected to the

chassis.

Motor

Voltage (V)

Cold start capacity

CCA (Cold Cranking Amperes) (A)

Engines with Start/Stop*

800

All other engines

520–800

AGM (Absorbed Glass Mat) batteries have to be used on models with Start/Stop

Summary of Contents for 2016 XC60














































































































































































































































































































































































































Search results

Summary of Contents for 2016 XC60

Reviews:

Related manuals for 2016 XC60

Brands by name

Popular brands

Volvo 2016 XC60, Owner'S Manual

Search results

Summary of Contents for 2016 XC60

Reviews:

Related manuals for 2016 XC60

Brands by name

Popular brands