manualshive.com logo in svg

Vimar Elvox 46235.030D, Installation And Operation Manual, Page: 48 / 70

Share
Download
Vimar Elvox 46235.030D Installation And Operation Manual Download Page 48

   48

Graphic User Interface (GUI) for IP Speed Dome

EN

HTTP Port: The default HTTP port is 80. It can be changed to any port which is not occupied.

Data Port: The default data port is 9008. Please change it as required.

RTSP Port: The default port is 554. Please change it as required.

5.5.3 Central Server

This function is mainly used for connecting network video management system. 

1 - Check “Enable”.

2 - Check the IP address and port of the transfer media server in the CVM ELVOX. Then enable the auto report in the 

CVM ELVOX when adding a new device in the CVM ELVOX. Next, input the remaining information of the device. After 

that, the system will auto allot a device ID. Please check it in the CVM ELVOX.                        

3. Input the above-mentioned server address, server port and device ID in the responding boxes. Click “Save” button 

to save the settings.

5.5.4 DDNS Configuration

If your camera is set to use PPPoE as its default network connection, DDNS should be set for network access. 

Before you set the DDNS, please make sure you have registered a domain name on the DDNS server. 

1- Go to Config 

 Network 

 DDNS.

 

 

 

 

 

2-  Apply for a domain name. Take www. dvrdyndns.com for example.

 Input 

www.dvrdydns.com

 in the IE address bar to visit its website. Then click “Registration” button to register as 

shown below.

Summary of Contents for Elvox 46235.030D







































































Reviews:

No comments