manualshive.com logo in svg

Vimar Elvox 46235.030D, Installation And Operation Manual, Page: 32 / 70

Share
Download
Vimar Elvox 46235.030D Installation And Operation Manual Download Page 32

   32

Graphic User Interface (GUI) for IP Speed Dome

EN

5.4 Alarm Configuration

Alarm configuration includes four submenus: Motion Detection, Alarm In, Alarm Out and Alarm Server.

5.4.1 Motion Detection

To set motion detection: 

1 - Go to Config 

 Alarm 

 Motion Detection to set alarm trigger.

Check “Enable Alarm” check box to activate motion based alarm, choose alarm holding time and set alarm trigger 

options. 

Alarm Out:

 If selected, this would trigger the external relay output on detecting a motion based alarm. 

Trigger Snap:

 If selected, the system will snap images on an alarm and save them in SD card. 

Trigger SD Recording:

 If selected, video will be recorded on an SD card on motion detection.

Trigger Email:

 If the email and attach picture checkbox is checked (Email address shall be set first in the Mail config 

interface), the triggered snap pictures and event will be sent into those addresses. 

Trigger FTP:

 If “Uploading picture” is checked, the triggered snap pictures will be sent into FTP server address. Please 

refer to FTP configuration chapter for more details. 

2 - Set motion detection area and sensitivity. Click “Area and Sensitivity” tab to see the following sub-menu.

Summary of Contents for Elvox 46235.030D







































































Reviews:

No comments