ViaSat SurfBeam 2 Operation Manual Download Page 38

Page: 38 / 66

SurfBeam® 2 Pro Portable Terminal Operations Guide

Page 4-7

1172964, Rev. 002

ViaSat Proprietary Information

4.2.2.4

TRIA Page (TRIA Status)

The

TRIA

page (Figure 4-6) provides general information on the status of the TRIA.

Figure 4-6: Modem Web Interface – TRIA Page

General

Tx IF Power (dBm)

: Displays the IF power for the TRIA.

Tx RF Power (dBm)

: Displays the RF power for the TRIA.

Temperature (°C)

: Displays the ATRIA’s operation temperature.

Diagnostics

Brownout

and

Blueout Mode Enabled

: Displays “Yes” or “No” depending on system configuration.

TRIA Serial Number

: Displays the TRIA’s serial number.

TRIA Firmware Version

: Displays the TRIA’s firmware version.

Module Status

Bullfrog VG

Watchdog Timer

Tx/Rx PLL

, M

icroprocessor

Cable Resistance

and Temperature

: Displays or

depending on if the system has detected an issue.

Summary of Contents for SurfBeam 2



































































Search results

Summary of Contents for SurfBeam 2

Reviews:

Related manuals for SurfBeam 2

Brands by name

Popular brands

ViaSat SurfBeam 2, Operation Manual

Search results

Summary of Contents for SurfBeam 2

Reviews:

Related manuals for SurfBeam 2

Brands by name

Popular brands