ViaSat SurfBeam 2 Operation Manual Download Page 17

Page: 17 / 66

SurfBeam® 2 Pro Portable Terminal Operations Guide

Page 2-10

1172964, Rev. 002

ViaSat Proprietary Information

Step

Action

Image

23.

With the TRIA placed on a stable surface, remove the 90° Coax
Connector from the Accessory Bag and connect it to the TX/RX
port on the TRIA.

NOTE

: Ensure that the 90° connector is firmly attached (hand

tightened only).

NOTE

: This connector can be installed later as shown in Step 31.

24.

Holding the sides of the TRIA housing and from behind the Center
Reflector,

CAREFULLY

insert the Feedhorn through the reflector

hole until the base of the Feedhorn and TRIA alignment slots
contact the reflector hole and Assembly top-plate alignment
posts.

25.

Place one hand on the back of the TRIA housing and another on
the Assembly tower.

Gently

push and wiggle the TRIA housing

until it snaps into place.

26.

Hand tighten the large Collar Ring located between the TRIA
housing and reflector to connect the two components. Visually
inspect that the TRIA’s Feedhorn base is flush to the inside of the
Center Reflector.

27.

Visually inspect the TRIA to ensure no damage has occurred and
that the Splash Plate is properly seated on the Feedhorn.

28.

At the transit case, fold back the layer two and three dividers and

CAREFULLY

remove the modem assembly.

Summary of Contents for SurfBeam 2



































































Search results

Summary of Contents for SurfBeam 2

Reviews:

Related manuals for SurfBeam 2

Brands by name

Popular brands

ViaSat SurfBeam 2, Operation Manual

Search results

Summary of Contents for SurfBeam 2

Reviews:

Related manuals for SurfBeam 2

Brands by name

Popular brands