ViaSat SurfBeam 2 Operation Manual Download Page 6

Page: 6 / 66

SurfBeam® 2 Pro Portable Terminal Operations Guide

Page iv

ViaSat Proprietary Information

List of Tables

Table 2-1: Component Assembly List ...................................................................................................................................................................................... 2-4

Table 2-2: Unpack and Assembly Process................................................................................................................................................................................ 2-6

Table 2-3: Disassembly and Repacking Process ..................................................................................................................................................................... 2-13

Table 3-1: Pointing and Peaking Tone List ............................................................................................................................................................................... 3-1

Table 3-2: Modem Setup Process ............................................................................................................................................................................................ 3-2

Table 3-3: Baseline Elevation and Azimuth Setup Process ...................................................................................................................................................... 3-3

Table 3-4: Fine-tuning Azimuth and Elevation Setup Process.................................................................................................................................................. 3-5

Table 3-5: Modem Relocation Process .................................................................................................................................................................................... 3-7

Table 4-1: Operational Beam................................................................................................................................................................................................... 4-3

Table 4-2: System Operating State .......................................................................................................................................................................................... 4-3

Table 4-3: Router Firmware Update Process ......................................................................................................................................................................... 4-17

Table 5-1: Check-Out/Check-In Process .................................................................................................................................................................................. 5-1

Table 6-1: Hardware Troubleshooting ..................................................................................................................................................................................... 6-1

Table C-1: Configuration 1 – Polarization Identification .......................................................................................................................................................... C-4

Table C-2: Configuration 2 – Polarization Identification .......................................................................................................................................................... C-7

List of Figures

Figure 1-1: SurfBeam 2 Pro Portable ....................................................................................................................................................................................... 1-1

Figure 2-1: Antenna Transporting Restrictions ........................................................................................................................................................................ 2-3

Figure 2-2: Modem Assembly Transporting Restrictions ......................................................................................................................................................... 2-3

Figure 2-3: Component Assembly Layers ................................................................................................................................................................................ 2-4

Figure 4-1: Modem Assembly LCD Screen and User Interface................................................................................................................................................. 4-1

Figure 4-2: Modem Assembly LCD Menu Navigation Tree ...................................................................................................................................................... 4-1

Figure 4-3: Modem Web Interface .......................................................................................................................................................................................... 4-2

Figure 4-4: Modem Web Interface – Home Page .................................................................................................................................................................... 4-4

Figure 4-5: Modem Web Interface – Modem Page ................................................................................................................................................................. 4-5

Figure 4-6: Modem Web Interface – TRIA Page ...................................................................................................................................................................... 4-7

Figure 4-7: Router Web Interface Login Window .................................................................................................................................................................... 4-8

Figure 4-8: Router Web Interface ............................................................................................................................................................................................ 4-8

Figure 4-9: Router Web Interface – System Status Page ......................................................................................................................................................... 4-9

Figure 4-10: Router Web Interface – Router Status Page ...................................................................................................................................................... 4-10

Figure 4-11: Router Web Interface – LAN Setup Page ........................................................................................................................................................... 4-11

Figure 4-12: Router Web Interface – DHCP Setup Page ........................................................................................................................................................ 4-11

Figure 4-13: Router Web Interface – Port Forwarding Page .................................................................................................................................................. 4-12

Figure 4-14: Router Web Interface – Range Forwarding Page............................................................................................................................................... 4-12

Figure 4-15: Router Web Interface – DMZ Page .................................................................................................................................................................... 4-13

Figure 4-16: Router Web Interface – Routes Page ................................................................................................................................................................ 4-13

Figure 4-17: Router Web Interface – Password Page ............................................................................................................................................................ 4-14

Figure 4-18: Router Web Interface – Backup/Restore Page .................................................................................................................................................. 4-14

Figure 4-19: Router Web Interface – Firmware Upgrade Page .............................................................................................................................................. 4-15

Figure 4-20: Router Web Interface – Reboot Page ................................................................................................................................................................ 4-15

Figure 4-21: Router Web Interface – Utilities Page ............................................................................................................................................................... 4-16

Figure 5-1: Cable Connections ................................................................................................................................................................................................. 5-3

Figure C-1: KACST Pro Portable Polarization Identification Map ............................................................................................................................................. C-2

Figure C-2: Beam Selection for Identifying the Correct Co-Pol TRIA ........................................................................................................................................ C-3

Figure C-3: Co-Pol TRIA Components ................................................................................................................................................................................... C-4

Figure C-4: Uninstalling Feedhorn ........................................................................................................................................................................................... C-5

Figure C-5: Rotating Feedhorn ................................................................................................................................................................................................ C-5

Figure C-6: Reinstalling Feedhorn ............................................................................................................................................................................................ C-6

Figure C-7: TRIA Labeling ......................................................................................................................................................................................................... C-7

Summary of Contents for SurfBeam 2



































































Search results

Summary of Contents for SurfBeam 2

Reviews:

Related manuals for SurfBeam 2

Brands by name

Popular brands

ViaSat SurfBeam 2, Operation Manual

Search results

Summary of Contents for SurfBeam 2

Reviews:

Related manuals for SurfBeam 2

Brands by name

Popular brands