ViaSat SurfBeam 2 Operation Manual Download Page 64

Page: 64 / 66

SurfBeam® 2 Pro Portable Terminal Operations Guide

Page C-5

1172964, Rev. 002

ViaSat Proprietary Information

Uninstall the four hex screws from the base of the Feedhorn (refer to Figure C-4)

WARNING:

Proceed carefully with removing the Feedhorn, as protective Kapton tape is installed

between the horn base and Ortho Mode Transducer (OMT) housing. This tape needs to stay intact to
protect the unit from humidity, corrosion, and debris.

NOTE:

In the event the protective Kapton tape is damaged or lost, contact the KACST NOC for

instructions on moving forward with the installation.

Figure C-4: Uninstalling Feedhorn

Rotate the Feedhorn 90 degrees so the markings on the unit match those identified in step 5 (refer to Figure C-5)

Figure C-5: Rotating Feedhorn

Summary of Contents for SurfBeam 2



































































Search results

Summary of Contents for SurfBeam 2

Reviews:

Related manuals for SurfBeam 2

Brands by name

Popular brands

ViaSat SurfBeam 2, Operation Manual

Search results

Summary of Contents for SurfBeam 2

Reviews:

Related manuals for SurfBeam 2

Brands by name

Popular brands