VeEX MTTplus-900 User Manual Download Page 28

Page: 28 / 99

Utilization

: Reports the Channels with the highest utilization %. All channels in the 2.4 GHz and 5 GHz frequency band

are analyzed.

Top APs

: Reports the Channels where the most APs are configured. All channels in the 2.4 GHz and 5 GHz frequency

band are analyzed.

Top Users

: Reports the APs with the most associated clients. Note that not all APs report this information. If this

information is not reported by the AP, it will be ignored during the test.

Top Talkers

: Reports the APs with the highest utilization % (BSS load). Note that not all APs report this information. If this

information is not reported by the AP, it will be ignored during the test.

Note

: If AP Filter is enabled (see

AP Filter Setup

), only APs selected in the filter list are taken into account for these tests.

Go back to top

Go back to TOC

6.2.7 Connectivity Check Auto-Test

The following tests are performed during the Auto-Test Connectivity Check:

Note:

This test requires

AP Filter

enabled

(see

AP Filter Setup

). Only APs selected in the filter list are tested for connectivity. If

passwords are required, the user will be prompted to enter this information.

AP Login

Connection

: Reports the results of associating and connecting to the AP under test, including the assigned IP address.

Ping

: Reports the results of the Ping test. 5 Ping requests are sent to the Gateway’s IP address. The results PASS if the

WiFiAirExpertSeries_eManual_D07-00-120P_Rev A00

Summary of Contents for MTTplus-900




































































































Search results

Summary of Contents for MTTplus-900

Reviews:

Related manuals for MTTplus-900

Brands by name

Popular brands

VeEX MTTplus-900, User Manual

Search results

Summary of Contents for MTTplus-900

Reviews:

Related manuals for MTTplus-900

Brands by name

Popular brands