VeEX MTTplus-900 User Manual Download Page 20

Page: 20 / 99

Go back to top

Go back to TOC

5.2 WiFi Measurement Setup

WiFi Measurement Setup menu

Auto Connection

(WX150 only): Select enable to automatically connect to the last AP the test set was connected to.

Show Password

: From the drop-down menu, select

OFF

: The WiFi password is shown in plain text in the IP setup menu.

OFF

: The WiFi password is hidden in the IP setup menu.

Signal Level Threshold

: From the drop-down menu, select

Enable

Disable

Enable

: The values in the threshold setting will be used to display pass, warning, and fail results in the Coverage

Auto-test and AP scan menus.

Disable

: Signal levels will be ignored in the Auto-test and AP scan menus.

Noise Level Threshold

: From the drop-down menu, select

Enable

Disable

Enable

: The values in the threshold setting will be used to display pass, warning, and fail results in the Coverage

Auto-test and AP scan menus.

Disable

: Noise levels will be ignored in the Auto-test and AP scan menus.

Signal to Noise Ratio Threshold

: From the drop-down menu, select

Enable

Disable

Enable

: The values in the threshold setting will be used to display pass, warning, and fail results in the Coverage

Auto-test and AP scan menus.

Disable

: SNR will be ignored in the Auto-test and AP scan menus.

Channel Utilization Threshold

: From the drop-down menu, select

Enable

Disable

Enable

: The values in the threshold setting will be used to display pass, warning, and fail results in the Coverage

Auto-test and AP scan menus.

Disable

: Utilization will be ignored in the Auto-test and AP scan menus.

Co-Channel Interference Threshold

: From the drop-down menu, select

Enable

Disable

Enable

: The values in the threshold setting will be used to display pass, warning and fail results in the Interference

Auto-test.

Disable

: Co-Channel Interference will be ignored in the Interference Auto-test.

Adjacent Channel Interference Threshold

: From the drop-down menu, select

Enable

Disable

Enable

: The values in the threshold setting will be used to display pass, warning, and fail results in the Interference

Auto-test.

Disable

: Adjacent Channel Interference will be ignored in the Interference Auto-test.

WiFiAirExpertSeries_eManual_D07-00-120P_Rev A00

Summary of Contents for MTTplus-900




































































































Search results

Summary of Contents for MTTplus-900

Reviews:

Related manuals for MTTplus-900

Brands by name

Popular brands

VeEX MTTplus-900, User Manual

Search results

Summary of Contents for MTTplus-900

Reviews:

Related manuals for MTTplus-900

Brands by name

Popular brands