VALCO MELTON MCP-8I Quick Start Manual Download Page 10

Page: 10 / 63

www.valcomelton.com | TEL: (1) 513-874-6550 | FAX: (1) 513-874-3612

Doc. IS0xxx

Rev.04 | Date: August 25, 2021

MCP-8I Quick Start Guide

Inspection Details Explained

Understanding Inspection Window Graphics

On the ‘

Inspection Window

’ the displayed pattern graphic contains useful relative to the

inspection process and analysis.

Figure 16: Inspection Window

Measured Pattern Length

The

Measured Pattern Length

is displayed in the center of the Glue Inspection Graphic, above

the Glue Pattern Animation.

Figure 17: Glue Pattern Graphic (Pattern Length)

Pattern Index

The

Pattern Index

is displayed in the center of the Glue Pattern Animation that is drawn on top

of the Glue Inspection Tolerance Graphic.

Figure 18: Glue Pattern Graphic (Pattern Index)

Summary of Contents for MCP-8I
































































Search results

Summary of Contents for MCP-8I

Reviews:

Related manuals for MCP-8I

Brands by name

Popular brands

VALCO MELTON MCP-8I, Quick Start Manual

Search results

Summary of Contents for MCP-8I

Reviews:

Related manuals for MCP-8I

Brands by name

Popular brands