VALCO MELTON MCP-8I Quick Start Manual Download Page 54

Page: 54 / 63

www.valcomelton.com | TEL: (1) 513-874-6550 | FAX: (1) 513-874-3612

Doc. IS0xxx

Rev.04 | Date: August 25, 2021

MCP-8I Quick Start Guide

How to Configure the CGS Sensor for a Continuous Gluing Application

The ‘

Encoders Z-Pulse

’ will be used to trigger the CGS Sensor’s Inspection Evaluation Process.

The Sensor Channel’s ‘

Scanner

’ parameter will need to be set to ‘

Z-Signal Encoder

’.

The Sensor Channel’s ‘

Distance to Scanner

’ parameter should be set to 0 mm.

The Sensor Channel’s ‘

Reference Mode

’ parameter should to be set to ‘

Manual

’.

The Sensor Channel’s ‘

Glue Correction – Start / End

’ parameters should be set to 0 mm.

Each of these parameters are found under the ‘

Inspection Channel’s Settings Menu

’.

Here are instructions to navigate to the settings menu:

1. Navigate to the

‘Inspection Window’

by pressing the button labeled ‘

INSPECT

’.

Figure 112: Navigating to the Inspection Window

2. Navigate to the ‘

Inspection Channel’s Settings Menu

’ by pressing the ‘

Wrench

’ button.

Figure 113: Navigating to the Sensor Channel's Settings

3. Find and set each of the parameters mentioned above in the parameter list.

Summary of Contents for MCP-8I
































































Search results

Summary of Contents for MCP-8I

Reviews:

Related manuals for MCP-8I

Brands by name

Popular brands

VALCO MELTON MCP-8I, Quick Start Manual

Search results

Summary of Contents for MCP-8I

Reviews:

Related manuals for MCP-8I

Brands by name

Popular brands