VALCO MELTON MCP-8I Quick Start Manual Download Page 62

Page: 62 / 63

www.valcomelton.com | TEL: (1) 513-874-6550 | FAX: (1) 513-874-3612

Doc. IS0xxx

Rev.04 | Date: August 25, 2021

MCP-8I Quick Start Guide

5. Now that the data is loaded, you can run simulations by clicking the ‘

Run Simulation’

button at the top of the application. If the simulation passed you will see the green result

light next to the sensor activation button. If the simulation failed you will see the red result

light next to the sensor activation button.

Figure 128: MCP8I Simulator Run Simulation Button

Note1

– The Simulator was orginally meant just to show the different control windows and

parameters. The MCP8I Simulator allows the user to run the simulation code based on the

settings that are set. That being said, you can changes settings and rerun the simulation and get

different results.

Note2

– The Simulator has the ability to show the Inspection Alarm States. This is only available

for the Inspection Simulation and the Alarm Beacon States for other control features are not

included.

Note3

– The Simulator may have a software bug or two, since it is more of a development tool,

not much time has been spent on enhancing its features. If you do encounter an issue, please

send and email to ‘[email protected]’, and I will try to resolve it with a reasonable

time.

Summary of Contents for MCP-8I
































































Search results

Summary of Contents for MCP-8I

Reviews:

Related manuals for MCP-8I

Brands by name

Popular brands

VALCO MELTON MCP-8I, Quick Start Manual

Search results

Summary of Contents for MCP-8I

Reviews:

Related manuals for MCP-8I

Brands by name

Popular brands