VALCO MELTON MCP-8I Quick Start Manual Download Page 56

Page: 56 / 63

www.valcomelton.com | TEL: (1) 513-874-6550 | FAX: (1) 513-874-3612

Doc. IS0xxx

Rev.04 | Date: August 25, 2021

MCP-8I Quick Start Guide

4. Select

each

of the desired ‘

Alarm Activation

’ parameters that need to be suppressed until

the machine speed is above the Sensor Channel’s ‘

Vmin

’ speed, and select the activation

mode to ‘

ON > Vmin

’. Then press the button labeled ‘

APPLY

’.

Figure 117: Setting Alarm On Above Vmin

5. In the same menu, Select the Sensor Channel’s ‘

Vmin

’ setting. Using the thumbwheel

buttons, set the desired machine speed at which the desired alarms can be activated and

press the button labeled ‘

APPLY

’.

Figure 118: Setting the Sensor Channel's Vmin Setting

Note1 –

Products that fail and have the alarm activation suppressed will still be shown on the

control’s display and will be counted in the ‘

Inspection Statistic’s

’ as an

Error.

Note2

– Alarm Activation Suppression

must

be configured for each Inspection Channel.

Summary of Contents for MCP-8I
































































Search results

Summary of Contents for MCP-8I

Reviews:

Related manuals for MCP-8I

Brands by name

Popular brands

VALCO MELTON MCP-8I, Quick Start Manual

Search results

Summary of Contents for MCP-8I

Reviews:

Related manuals for MCP-8I

Brands by name

Popular brands