US Water Systems 385-GWU-1000 Owner'S Manual Download Page 20 | Manualshive

Page: 20 / 53

background image

20

2. Lubricate the distributor O-ring and the tank O-ring.  Then install the upper basket (may
look different than the pictures below) on the bottom of the valve by lining up the tabs then
turning the basket clockwise to lock it in place.  Place the upper basket over the distributor
tube and push the valve on the tank.  Thread the valve on the tank by turning it clockwise.
Be sure not to cross-thread the valve on the tank.  Tighten the valve hand tight, then snug it
further by tapping it with the palm of the hand.  DO NOT use tools to tighten the valve or
damage could occur. Move the carbon unit to the side and start the injection panel installa-
tion

Superfilter Tank and Control Valve Preparation

Installation, Operation and Maintenance Manual

385-GWU-1000, 385-GWU-1500, 385-GWU-2000

«
...
18
19
20
21
22
...
»

Summary of Contents for 385-GWU-1000






















































Reviews:

No comments

Related manuals for 385-GWU-1000

Brand: Nelson Pages: 14

RainStation RS-0001

Brand: EarthMinded Pages: 16

Brand: Atlas Copco Pages: 40

Brand: Viking Pages: 11

Brand: ubbink Pages: 54

aquaMAX-Basic 360 Series

Brand: Young Lin Pages: 35

Brand: Mitsubishi Pages: 15

PUR Smart 800 PRO

Brand: purway Crystal Group Pages: 14

Brand: TOOLCRAFT Pages: 12

Brand: Kenmore Pages: 12

Brand: Kenmore Pages: 20

Brand: Kenmore Pages: 12

Brand: Kenmore Pages: 12

Brand: Kenmore Pages: 20

Brand: Kenmore Pages: 20

Brand: Kenmore Pages: 28

Brand: Kenmore Pages: 18

Brand: Kenmore Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands