US Water Systems 385-GWU-1000 Owner'S Manual Download Page 49 | Manualshive

Page: 49 / 53

background image

49

WARNING!  Be sure the peroxide injection pump is adjusted properly before bringing the
GreenWave tank into service.  Iron or other contaminants that are removed by the perox-
ide injection system can damage the GreenWave media.  It is crucial that the peroxide
system is operating properly.

GreenWave Tank Startup Instructions

Installation, Operation and Maintenance Manual

385-GWU-1000, 385-GWU-1500, 385-GWU-2000

1. The GreenWave tank should be in “bypass” - shown below.
2. Open a spigot downstream of the system and slowly open both bypass valves on the

GreenWave tank. Just slightly open the valves at first and let the air start to purge from that
tank.

WARNING! Do not open the valves completely until the air is purged from the Green-

Wave tank or damage could occur.

3. Run the water for several minutes or until clear and the air has been purged from the

GreenWave tank and the entire system. Then fully open the bypass valves on the Green-
Wave tank.

4. Confirm that there are no leaks and plug the US Water UV light into the 110v GFI outlet.
5. The system is now operational and the startup is complete.

Service

Position

UP-Flow Tank

Bypass

Position

UP-Flow Tank

«
...
47
48
49
50
51
...
»

Summary of Contents for 385-GWU-1000






















































Reviews:

No comments

Related manuals for 385-GWU-1000

AQUAGUARD CREST UV +HOT

Brand: Eureka Forbes Pages: 13

Brand: HQRP Pages: 37

Pure H2O H2O-DWUF300

Brand: Watts Pages: 32

Brand: Aqua Free Pages: 2

Brand: NatureWater Pages: 5

Brand: Econ Pages: 7

Brand: IKEA Pages: 2

OptimH2O EQ-OPTM

Brand: Aquasana Pages: 12

Gem AQUARIUS F990

Brand: Tyco Fire Product Pages: 12

Brand: Geovent Pages: 4

Brand: Softena Pages: 48

Brand: Garden Treasures Pages: 2

Brand: blupura Pages: 28

Brand: BWT Pages: 56

Brand: GE Pages: 26

Brand: GE Pages: 4

Culligan FXRT12

Brand: GE Pages: 4

Brand: GE Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands