background image

 

 

 

 

The GreenWave Ultra system provides protection from scale formation throughout the home. 
The GreenWave system should be installed after the Fusion Oxi-Gen system to treat your 
entire home, both hot and cold water, or it can be located directly before a water heater or 
other device (e.g. sauna, etc) that requires protection from hard water. 
 
The GreenWave Ultra reduces or eliminates scale formation on internal and external plumbing 
surfaces as well as reducing spotting and streaking normally associated with hard water. 
 
The GreenWave Ultra prevents scale by transforming the normal dissolved hardness minerals 
into undissolved crystal micro-particles. These crystals stay suspended in the water and 
dramatically reduce the scaling potential of hardness minerals. Therefore the problem of 
internal build¬up of scale in pipes, water heaters and on fixtures and glass is greatly reduced. 
 
The GreenWave Ultra is not a water softener – Low or phosphate-free cleaning products are 
recommended to achieve optimum results. Modern surfactant or detergent based, liquid soaps 
are preferred over old-fashioned fashioned caustic solid soaps. 
 
Unlike softened water, the GreenWave Ultra treated water maintains the beneficial essential 
mineral content of your water and is safe to drink. 
 

GreenWave Tank Benefits 
 

 

Chemical Free Scale Prevention. Cost savings and environmental benefits 

 

Virtually Maintenance Free. No salt bags or other chemicals to buy, transport and store 

 

Beneficial minerals retained for more healthful drinking water 

 

Improves the efficiency of water-using appliances 

 

Simple installation – no electrical and drain hookup 

 

Safe for landscaping and lawn watering. No need for costly plumbing bypasses  

 

Compatible with all on-site and community wastewater treatment systems 

 

Not subject to water softener restrictions and "bans" 

GreenWave Tank Introduction 

Installation, Operation and Maintenance Manual 

 

385-GWU-1000, 385-GWU-1500, 385-GWU-2000 

Summary of Contents for 385-GWU-1000






















































Reviews: