Task Force Tips MASTER FOAM Instructions For Safe Operation And Maintenance Download

Page: 1 / 12

INSTRUCTIONS FOR SAFE OPERATION AND MAINTENANCE

MASTER FOAM

FIXED

SELF-EDUCTING

FOAM NOZZLE

GPM

TASK FORCE TIPS

800.348.2686

www.tft.com

Fixed Flow

Rate:

Nominal

Pressure:

Nominal Foam

Percentages:

350, 500,

or 750 GPM

100 PSI

0.5%, 1%,

3%, or 6%

Read instruction manual before use. Operation of this device without

understanding the manual and receiving proper training is a misuse of this

equipment. A person who has not read and understood all operating and

safety instructions is not qualified to operate the MASTER FOAM self-

educting nozzle.
This instruction manual is intended to familiarize firefighters and

maintenance personnel with the operation, servicing, and safety

procedures associated with the MASTER FOAM self-educting nozzle.
This manual should be kept available to all operating and maintenance

personnel.

WARNING

Summary of Contents for MASTER FOAM













Search results

Summary of Contents for MASTER FOAM

Reviews:

Related manuals for MASTER FOAM

Brands by name

Popular brands

Task Force Tips MASTER FOAM, Instructions For Safe Operation And Maintenance

Search results

Summary of Contents for MASTER FOAM

Reviews:

Related manuals for MASTER FOAM

Brands by name

Popular brands