US Water Systems 385-GWU-1000 Owner'S Manual Download Page 42 | Manualshive

Page: 42 / 53

background image

42

3. Now mount the filter housing to the wall using the appropriate fasteners for your wall materi-

al. It is preferred that this is mounted on a secured board or wall stud as it will be heavy
when full of water.

4. The outlet plumbing from the UV light will connect to the “IN” port on the filter housing. The

outlet plumbing from the sediment filter housing will be connected to the plumbing distribu-
tion system for the home.

1 Micron Sediment Filter Installation Instructions

Installation, Operation and Maintenance Manual

385-GWU-1000, 385-GWU-1500, 385-GWU-2000

«
...
40
41
42
43
44
...
»

Summary of Contents for 385-GWU-1000






















































Reviews:

No comments

Related manuals for 385-GWU-1000

Brand: ubbink Pages: 55

Brand: Xsential Pages: 2

Brand: Nelson Pages: 24

Brand: IMI NORGREN Pages: 5

CertiSafe PM-100

Brand: Kasco Pages: 19

Brand: Super Pages: 13

Brand: Super Pages: 18

Brand: Wieland Pages: 40

Brand: HYDAC FILTER SYSTEMS Pages: 44

Brand: HYDAC FILTER SYSTEMS Pages: 64

PROKLIMA 28155346

Brand: BAHAG Pages: 2

Brand: YAMIT Pages: 36

Brand: Mountain Fresh Pages: 2

Brand: Hydac Pages: 44

Brand: VacPak-It Pages: 7

Brand: EcoWater Pages: 42

Brand: Pico Macom Pages: 2

Brand: Watts Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands