US Water Systems 385-GWU-1000 Owner'S Manual Download Page 32 | Manualshive

Page: 32 / 53

background image

32

1. Now install the filter in the filter housing by removing the sump from the housing.
2. There is a notch in the bottom of the sump that will center the filter in the housing. Unwrap

the filter (5 Micron) and install it in the sump.

3. Coat the O-ring and threads on the sump with food grade silicone grease and install the O-

ring in the filter sump.

Sediment Filter Installation Instructions

Installation, Operation and Maintenance Manual

385-GWU-1000, 385-GWU-1500, 385-GWU-2000

«
...
30
31
32
33
34
...
»

Summary of Contents for 385-GWU-1000






















































Reviews:

No comments

Related manuals for 385-GWU-1000

Brand: Wayne Pages: 16

Aqua-Pure AP717

Brand: 3M Pages: 12

Aqua-Pure AP1610SS

Brand: 3M Pages: 2

AQUA-PURE IL-IM-01

Brand: 3M Pages: 2

Aqua-Pure AP200

Brand: 3M Pages: 2

Aqua-Pure AP510

Brand: 3M Pages: 16

High Flow Series

Brand: 3M Pages: 8

Brand: Jura Pages: 11

Brand: Finerfilters Pages: 15

AQUA OCEAN AQ4000

Brand: ICA Pages: 16

Brand: Wavin-Labko Pages: 11

Brand: Madas Pages: 44

Brand: RAINSHOWER Pages: 2

acura Line ALGS

Brand: FUHR Pages: 11

PUR Smart 800 PRO

Brand: purway Crystal Group Pages: 14

MultiCyclone12 Plus

Brand: Waterco Pages: 12

Brand: Lunt Solar Systems Pages: 4

Aquajoe AJ-OMS18-TRB

Brand: SNOWJOE Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands