TYM TX1500 Manual Download Page 142

Page: 142 / 218

4 - 8

Work Procedure

3. tyPes of Work by sPeed table

The tractor speeds specified in the table on the right side are recommended

by types of work for optimum efficiency.

Increase or decrease the tractor speed according to the soil and work condi-

tions.

This chapter only provides brief descriptions and instructions for a rotavator

and loader. Therefore, for detailed operational instructions and other descrip-

tions, refer to the user's manual of each implement.

•

NOTE

993E009a

Do not let anyone ride a loader for

work, such as spreading fertiliz-

er. He/she may fall off the loader,

leading to an injury or even death.

•

WARNING

Driving speed table

* The applicable works by speed mentioned above can vary by soil conditions.

Select appropriate speed according to the work condition.

Tra

cto

Pla

nte

tar

rro

Plo

Driving

Vehicle speed

(km/h)

Engine: ,00 RPM as standard

Full engine speed

Applicable

work

Creep speed mode

Normal mode

TX1500-영문-04(라).indd 8

2012-12-17 오후 2:27:00

Summary of Contents for TX1500



























































































































































































































Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands

TYM TX1500, Manual

Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands