TYM TX1500 Manual Download Page 111

Page: 111 / 218

2 -

DESCRIPTION OF OPERATING SYSTEM

TX1O368A

Drawbar

DRAwBAR ADJuSTMENT

Adjust the drawbar as follows:

- Use the fixing pin (1) to prevent

any lateral sway.

- To adjust the distance between

the PTO and drawbar, move the

fixing pin to another hole in the

drawbar.

►

P.T.O. ShAFT CAP

When the PTO shaft is not in use,

grease the PTO shaft and install the

cap to it.

►

TX1O369A

PTO

Shaft cap

If caught by the PTO shaft, it can

lead to a severe injury or even

death. Never get close to the PTO

shaft while it is rotating.
When the PTO shaft is not in use,

place the cap over it. Also, never

remove the PTO safety cover.

•

DANGER

It is dangerous to use an imple-

ment at a high speed if it is de-

signed to be operated at a low

speed.
Before using an implement, make

sure to read its owner's manual.

•

CAUTION

TX1500-영문-02(나).indd 55

2012-12-17 오후 2:25:43

Summary of Contents for TX1500



























































































































































































































Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands

TYM TX1500, Manual

Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands