TYM TX1500 Manual Download

Page: 88 / 218

2 - 2

2 -

DESCRIPTION OF OPERATING SYSTEM

2 - 2

2 -

<Manual mode>

When the upper section of the

Up/Down switch is pressed, the

manual mode is activated and

the front axle is lifted. When the

lower section of the switch is

pressed, the axle is lowered.
When the height is adjusted in

the manual mode, the adjusted

height is maintained.
This mode can be used to adjust

the height of the front axle.

•

Use the manual mode for cultivat-

ing and working with a loader.
When the engine is stopped, the

system is returned to the manual

mode.

•

NOTE

When the driving speed is over 1

km/h, the automatic mode is auto

matically selected.

•

NOTE

(17) limp home mode switch

This switch is used to operate only

minimal necessary devices in case

of machine failure so that the tractor

can be driven to a workshop.
Use this only when driving the trac-

tor is impossible.

Pressing the upper section of the

switch drives the tractor forward.
Pressing the lower section of the

switch drives the tractor backward.
Most systems, except the hydrau-

lic system, are not operational.

•

Limp home mode switch

TX1O338A

Pressing the upper section of the

automatic mode switch activates

the automatic mode. Pressing it

again activates the manual mode.

<Block mode>

This mode is used to move the

front axle to the lowest position.
When pressing the upper sec-

tion of the automatic mode

switch, the system enters the

block mode and the front axle is

moved to the lowest position.
This is useful when trying to low-

er the tractor height or changing

hydraulic fluid.

•

TX1500-영문-02(나).indd 32

2012-12-17 오후 2:25:07

Summary of Contents for TX1500



























































































































































































































Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands

TYM TX1500, Manual

Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands