TYM TX1500 Manual Download Page 150

Page: 150 / 218

5-8

Maintenance

changing frOnt axle Oil

(1) changing oil for differential section

①

beforedrainingoil,unscrewthebleedertoreleasetheinternalpressure.

②

Unscrew the drain plug at the back to drain oil. As hot oil flows out of the

engine first, be careful not to get burnt.

③

afterdrainoilcompletely,tightenthedrainplug.

④

Unscrew the filler plug on the front and add the specified amount of oil.

⑤

Tighten the filler plug. Then, tighten the bleeder.

►

ifengineoilgetsonyourskin,it

canirritatetheskinandcausea

skincondition.makesuretoclean

yourskinwithsoapandwateror

handcleanerthoroughly.

•

CAUTION

TX1O601A

bleeder

drain

hole

TX1O602A

filler

hole

bleeder

TX1500-영문-05(마).indd 8

2012-12-17 오후 2:43:56

Summary of Contents for TX1500



























































































































































































































Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands

TYM TX1500, Manual

Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands