TYM TX1500 Manual Download Page 64

Page: 64 / 218

2 - 8

2 - 9

DESCRIPTION OF OPERATING SYSTEM

2 - 8

2 - 9

(4) Fuel gauge

This indicates the amount of fuel

while the main switch is in the "ON"

position.

: Full

: Empty

•

(5) Coolant temperature gauge

This indicates the temperature of

coolant while the main switch is in

the "ON" position.

: Cold

: Hot

If the needle is in the red "H" zone

during driving, the coolant is over-

heated. In this case, stop driving

and take any necessary action ac-

cording to the troubleshooting in-

structions.

•

(6) Tractor left turn signal indica-

tor (green)

This indicates the turn signal lamp

operation with the column lever.

This blinks along with the left turn

signal lamp.

(7) Tractor right turn signal indi-

cator (green)

This indicates the turn signal lamp

operation with the column lever.

This blinks along with the right turn

signal lamp.

TX1O313A

TX1O314A

TX1O315A

Poor fuel quality can damage the

engine. Make sure to use only the

specified genuine Diesel fuel.

Use fuel for winter season in win-

ter to enhance engine starting per-

formance.

•

NOTE

TX1500-영문-02(나).indd 8

2012-12-17 오후 2:24:46

Summary of Contents for TX1500



























































































































































































































Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands

TYM TX1500, Manual

Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands