TYM TX1500 Manual Download Page 18

Page: 18 / 218

FOR SAFE OPERATION

- 14

WARNING

Put the main shift lever into

「

neu-

tral

」

position.



Check the area around the ma-

chine and give signal before

starting the engine.



Disengage the clutch and then

start the engine.

To warm up (idling) the engine,

move the main shift lever and

range shift lever into the

「

neu-

tral

」

position and apply the parking

brake on the level ground.

llo

t F

llo

When driving backward from low

roof storage,

「

disengage

」

the

planting clutch, lower down the

planting part and place the planting

clutch lever at

「

fixed

」

position.

If the shift gear or clutch is not dis-

engaged, the machine can move

abruptly and cause an accident.

If the machine move abruptly, it

may cause an accident.

If the planting part is raised unex-

pectedly, it may cause an accident.

TX1500-영문-00(안).indd 14

2012-12-17 오후 2:22:18

Summary of Contents for TX1500



























































































































































































































Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands

TYM TX1500, Manual

Search results

Summary of Contents for TX1500

Reviews:

Related manuals for TX1500

Brands by name

Popular brands