Tuttnauer 2301006 Operation & Maintenance Manual Download Page 73 | Manualshive

Page: 73 / 122

background image

Page 68 of 117 pages

6.

TRANSPORTATION OF THE AUTOCLAVE

To facilitate transporting the autoclave through narrow passageways, the
cabinet is made in two sections. After transporting the autoclave to its
destination reassemble.

1.

Remove all the bolts which tighten the control panel with the
autoclave panel (2,3).

2.

Remove the bolts that tighten the control base to the autoclave base
(1).

3.

Disconnect the multi-pins connector mounted on the main electric
box.

4.

Separate the two autoclave parts.

After the autoclave has been installed at the desired location, connect the
two parts according to the reverse order of the directions given for
dismantling.

Top View

«
...
71
72
73
74
75
...
»

Summary of Contents for 2301006



























































































































Reviews:

No comments

Related manuals for 2301006

ACS880-01 Series

Brand: ABB Pages: 238

Brand: Hagie Pages: 61

Tetrix 351 AC/DC Smart FW

Brand: EWM Pages: 117

Brand: BACtrack Pages: 13

Brand: TA Instruments Pages: 35

Brand: idiag Pages: 12

Brand: Zenbooth Pages: 60

Brand: KaVo Pages: 49

Brand: Easson Pages: 33

Brand: LAPPSET Pages: 16

Brand: S.R.Smith Pages: 8

Brand: S.R.Smith Pages: 23

NavBoard ZipFlip

Brand: S&S Precision Pages: 6

Brand: XanLite Pages: 4

Brand: Zimmer Pages: 54

Brand: Zimmer Pages: 4

Brand: Zimmer Biomet Pages: 23

Brand: Zimmer Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands