Tuttnauer 2301006 Operation & Maintenance Manual Download Page 119 | Manualshive

Page: 119 / 122

background image

Page 114 of 117 pages

Can not upload Parameters!

Description:

This message may be displayed during download process, when

the program is trying to upload Parameters.

Reason:

Probably a communication failure between PCS Target and the PC.

Tips:

Check if communication RS232 cable is connected. If it is a modem

connection, check if Modem cable is connected in this case it can be that the
remote modem cable is disconnected or RS232 cable between the remote
modem and the target platform is disconnected.

Fail download program!

Description:

This message may be displayed during download process, when

the program is trying to download the code file.

Reason:

Probably a communication failure between PCS Target and the PC, or

downloaded file is wrong or damaged.

Tips:

1. Check if communication RS232 cable is connected. If it is a modem

connection, check if Modem cable is connected in this case it can be that the
remote modem cable is disconnected or RS232 cable between the remote
modem and target platform is disconnected.
2. Try to download another file.

Fail download Parameters

!

Description:

This message may be displayed during download process, when

the program is trying to download Parameters.

Reason:

Probably a communication failure between PCS Target and the PC, or

PCS target platform is damaged and can not save data on flash memory.

Tips:

1. Check if communication RS232 cable is connected. If it is a modem

connection, check if Modem cable is connected in this case it can be that the
remote modem cable is disconnected or RS232 cable between the remote
modem and target platform is disconnected.
2. Try to change the target electronic card.

Fail Downloading Gain and Offset!

Description:

This message may be displayed during download process, when

the program is trying to download Gain and Offset values.

Reason:

Probably a communication failure between PCS Target and the PC, or

PCS target platform is damaged and can not save data on flash memory.

Tips:

1. Check if communication RS232 cable is connected. If it is a modem

connection, check if Modem cable is connected in this case it can be that the
remote modem cable is disconnected or RS232 cable between the remote
modem and target platform is disconnected.
2. Try to change the target electronic card.

«
...
117
118
119
120
121
...
»

Summary of Contents for 2301006



























































































































Reviews:

No comments

Related manuals for 2301006

Brand: ABB Pages: 11

Brand: vanEE Pages: 52

Brand: Caddon Hives Pages: 3

Brand: Danelec Pages: 67

Brand: h/p/cosmos Pages: 81

Brand: LAPPSET Pages: 16

Brand: Yamaha Pages: 39

Brand: Yamaha Pages: 110

Brand: Yuwell Pages: 2

Brand: York International Pages: 16

Brand: X-10 Pages: 12

Brand: Equinox Systems Pages: 8

Brand: Poulan Pro Pages: 17

IQ Express RF6118

Brand: Mainpine Pages: 2

Brand: BRAND Pages: 21

Brand: Milestone Pages: 40

Firefly 808 Universal

Brand: Phonic Pages: 27

LED PL G24d TC-D

Brand: Bailey Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands