manualshive.com logo in svg

Tuttnauer 2301006, Operation & Maintenance Manual, Page: 102 / 122

Share
Download
Tuttnauer 2301006 Operation & Maintenance Manual Download Page 102

Page 97 of 117 pages  

13.

VALVES NUMBERING

The valves in the drawing and the manual are numbered according to

their function. The following list includes all the valve numbers that are

in use in Tuttnauer.

0.

FUNCTION

01.

Change-over : steam / electricity

02.

Locking door cylinder (front door)

03.

Locking door cylinder (Rear door)

1.

FEED WATER

11.

Feed water – cool  jacket

12.

Feed water – cool heat  exchanger

13.

Feed water – cool fast exhaust

14.

Feed water – to reservoir

15.

feed water – to vacuum pump/ ejector

16.

Water outlet

17.

Shut

18.

Feed water – to air detector

2.

MINERAL FREE
WATER

21.

Mineral free water - inlet

22.

Detergent

23.

To spray

24.

Recycling inlet

25.

Recycling outlet

3.

COMPRESSED
AIR

31.

Air inlet

32.

Air inlet - to chamber

33.

To splash cooling pipe

34-1. To door 1 seal
34-2. To door 2 seal
38-1. Open door 1
38-2. Open door 2
39-1. Close door 1
39-2. Close door 2

4.

AIR

41.

Air release N.C.

42.

Air release N.O.

43.

Filtered air - inlet

44.

Air Inlet

45.

Air Leak Test

Summary of Contents for 2301006



























































































































Reviews:

No comments