Tsuruga 8527 Instruction Manual Download Page 47

Page: 47 / 112

13. Special test mode

Model

8527

is able to have the setting of 4 special functions by means of key operation on

the front panel.

(1) Double action start function

Within 0.5 second from the stop signal having been input, the test starts with input of
start signal.

Note

: When the function is set,

READY

lamp blinks in READY status.

(2) GOOD hold function

This is the function to concern the good judgement. The output becomes continuous
until the stop signal is input.

(3) Momentary start function

The test is done only when the start signal is input.

(4) FAIL mode function

This is the function to disable the resetting of NG judgement and PROTECTION
action by the stop signal of remote control, and enables the resetting only by the stop
switch on the tester main unit.

Setting procedure of special test mode

①

In READY status, press

SHIFT

and

STOP

key at a time for 3 seconds or more.

READY

lamp blinks and the test time display is lit up with “

”.

The 4th digit of the current/resistance display blinks.

②

The item to set can be moved with

key.

③

Refer to the following table for the items to select.

CURRENT/RESISTANCE

▲

key: Numeral increases.

▼

key: Numeral decreases.

Lamps to synchronously blinks

at the setting

Cancel of setting

READY

lamp

Setting of double action start function

Cancel of setting

GOOD

I-TEST

W-TEST

Setting of GOOD hold function

Note

: In order to re-start, once of stop

signal input is necessary

Setting of GOOD hold function

Note

: When the start signal is input, the

judgement output is reset and

re-starts.

Cancel of setting

I-TEST

W-TEST

lamp

Setting of momentary start function

Cancel of setting

HIGH

LOW

I-TEST

W-TEST

Setting of FAIL mode

Finish of setting

Press

ENTER

key, then the tester returns to READY status, memorizing the set having

been made.
When the

EXIT

key (

SHIFT

and

ENTER

at a time) is pressed in the setting mode,

the special test mode is interrupted and the tester becomes READY status.

The special test mode in this case is that before entering the special test mode.

ON/OFF

ENTER

WRITE

READ

LOCK

○

BUZZER

READY

REMOTE

DISCHARGE

KEY LOCK

EXIT

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

SHIFT

LOW

HIGH

LOW

HIGH

LOW

○

W-TEST

○

MEMORY

SET

No.

HIGH

○

I-TEST

I-W

W-I

◎

GOOD

Double action

GOOD hold

Momentary

FAIL mode

Summary of Contents for 8527

















































































































Search results

Summary of Contents for 8527

Reviews:

Related manuals for 8527

Brands by name

Popular brands

Tsuruga 8527, Instruction Manual

Search results

Summary of Contents for 8527

Reviews:

Related manuals for 8527

Brands by name

Popular brands