Tsuruga 8527 Instruction Manual Download Page 36

Page: 36 / 112

Setting of test condition for insulation resistance test

[When setting the test time]

To enter setting mode

①

In READY status, press

key, then the test mode lamp blinks.

Test mode lamp moves up and down with

▲

▼

key. Make the required test

mode lamp blinking (

W-I

I-W

lamp).

②

Press

key and make the test mode lamp lit.

Setting of test time

①

Press

key and select the status that the test time display blinks.

②

Next, press

ON/OFF

key and select the status that the display blinks with the

numeral (refer to the above figure).

③

Press

▲

▼

key and set the test time.

Pressing of

key (

SHIFT

and

▲

at a time) or

key (

SHIFT

and

▼

at a time) allows the setting of second digit (digit of 1s).

To return to the previous setting

Press

key, then changes to the

setting of mask timer time

To the next setting

Press

key, then changes to the

setting of discharging function

Finish of setting

Press

ENTER

key, then the tester returns to READY status, memorizing the set having

been made.
The slider moves up or down when the test mode is W-I or I-W.
When the

EXIT

key (

SHIFT

and

ENTER

at a time) is pressed in the setting mode,

the setting mode for the test condition is interrupted and the tester becomes READY
status.

The test conditions in this case are those before entering the setting mode of test condition.

ON/OFF

ENTER

WRITE

READ

LOCK

○

BUZZER

READY

REMOTE

DISCHARGE

KEY LOCK

EXIT

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

SHIFT

GOOD

HIGH

LOW

GOOD

HIGH

LOW

○

W-TEST

○

MEMORY

SET

No.

HIGH

○

I-TEST

I-W

LOW

●

W-I

●

VOLTAGE SLIDER

Summary of Contents for 8527

















































































































Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands

Tsuruga 8527, Instruction Manual

Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands