Tsuruga 8527 Instruction Manual Download Page 59

Page: 59 / 112

18. Adjustment of buzzer sound

At the time of GOOD and NG judgement, the buzzer sounds.

Sound volume of the buzzer is adjustable by the setting on the front panel.

To enter the setting of buzzer sound

In READY status, press

ON/OFF

key and

▼

key at a time for 3 seconds or more.

The test time display is lit up with “

”.

Adjustment of buzzer sound at the GOOD judgement

①

The current/resistance display blinks with “

□

”.

The adjustment of buzzer sound at GOOD judgement can be made while “

□

” is

blinking.

②

The sound volume can be set with

▲

▼

key.

For the level of volume, refer to the table below.

Adjustment of buzzer sound at the NG judgement

①

The current/resistance display blinks with “

□

”.

②

With the

key, GOOD judgement “

□

”and NG judgement

“

□

” can be alternated. Select the blinking of NG judgement.

③

The sound volume can be set with

▲

▼

key.

For the level of volume, refer to the table below.

Finish of setting

Press

ENTER

key, then the tester returns to READY status, memorizing the set having

been made.
When the

EXIT

key (

SHIFT

and

ENTER

at a time) is pressed while “

” is lit

up on the test time display displays , the adjustment of buzzer sound is interrupted and
becomes to READY status. The level of buzzer sound then is the level before entering
the setting of buzzer sound.

[Sound volume]

Adjustable range

Volume

For GOOD judgement For NG judgement

Max

↑

↓

Min

OFF

Buzzer sounds by pressing

STOP

switch

②

for confirmation.

ON/OFF

ENTER

WRITE

READ

LOCK

○

BUZZER

READY

REMOTE

DISCHARGE

KEY LOCK

EXIT

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

SHIFT

LOW

GOOD

HIGH

LOW

GOOD

HIGH

LOW

○

W-TEST

○

MEMORY

SET

No.

HIGH

○

I-TEST

I-W

W-I

VOLTAGE SLIDER

Summary of Contents for 8527

















































































































Search results

Summary of Contents for 8527

Reviews:

Related manuals for 8527

Brands by name

Popular brands

Tsuruga 8527, Instruction Manual

Search results

Summary of Contents for 8527

Reviews:

Related manuals for 8527

Brands by name

Popular brands