Tsuruga 8527 Instruction Manual Download Page 75

Page: 75 / 112

Explanation of communication method

3.2

●

Basic format of read-out command

When the “?” is added to the command letters sent from the host, 8527 transacts it as
read-out command. To the read-out command, 8527 adds “

parameter ” to the command

letters and transmits it to the host.

Command from the host side

: Command letters?

Response from 8527 to the host

: Command letters=parameter

In case of error, 8527 transmits the error code to the host.

Refer to the

article 6 (P34) Error

Example

3.6

Command

ILOW?



Reads out the low limit value of

resistance

insulation

resistance

test.

Response

ILOW=10.0MOHM



3.3

●

Basic format of setting and operation

○

When the “

” is added to the letters of setting command from the host side, 8527

transacts it as setting command.

○

“

” is not necessary for the operation command START and RESET.

Setting command from the host side

Command letters=

Operating command from the host side :

Command letters

Example 3.7 In case of setting command

Effective

command

MODE=WI



・・・・・

Test mode is set to W-I

Response

ERROR=0



・・・・・・

When Response Setting is ON.

Response

response

・・・・・・・・

When Response Setting is OFF.

In case of error, the error code is transmitted to the host.

Example 3.8 In case of operation command

Effective

command

case

START



Starts the test.

Response

ERROR=0



・・・・・・

When Response Setting is ON.

Response

response

・・・・・・・・・

When Response Setting is OFF.

In case of error, the error code is transmitted to the host.

Summary of Contents for 8527

















































































































Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands

Tsuruga 8527, Instruction Manual

Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands