Tsuruga 8527 Instruction Manual Download Page 30

Page: 30 / 112

9. Setting of test condition for insulation resistance test

The test condition can be set when the test mode W-I, I-W or I is selected.

9.1

●

Test range of insulation resistance test

Range to set: 1.0kV or 0.5kV

To enter setting mode

①

In READY status, press

key, then the test mode lamp blinks.

Test mode lamp moves up and down with

▲

▼

key. Make the required test

mode lamp blinking (

W-I

I-W

lamp).

②

Press

key and make the test mode lamp lit.

Change of test voltage range

①

Press

key and select the

I DC

lamp is lit up and the test voltage range

blinks (refer to the above figure).

②

Next, change the test voltage to 1.0kV or 0.5kV with

▲

▼

key.

When the test voltage is changed, the range display blinks with the selected voltage
value.

To move to the previous setting

Press

key and the setting changes as follows depending upon the test mode.

Test mode

Setting item after change

W-I

→

Setting of test time of w

ithstanding voltage test

I-W

→

Returns to the blinking of

I-W

test mode lamp.

→

Returns to the blinking of

test mode lamp.

To the next setting

Press

key, then changes to the

setting of high limit of resistance value

Finish of setting

Press

ENTER

key, then the tester returns to READY status, memorizing the set having

been made.
The slider moves up or down when the test mode is W-I or I-W.
When the

EXIT

key (

SHIFT

and

ENTER

at a time) is pressed in the setting mode,

the setting mode for the test condition is interrupted and the tester becomes READY
status.

The test conditions in this case are those before entering the setting mode of test condition.

ON/OFF

ENTER

WRITE

READ

LOCK

○

BUZZER

READY

REMOTE

DISCHARGE

KEY LOCK

EXIT

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

SHIFT

GOOD

HIGH

LOW

GOOD

HIGH

LOW

○

W-TEST

○

MEMORY

SET

No.

HIGH

○

I-TEST

I-W

LOW

●

W-I

●

VOLTAGE SLIDER

Summary of Contents for 8527

















































































































Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands

Tsuruga 8527, Instruction Manual

Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands