Tsuruga 8527 Instruction Manual Download Page 16

Page: 16 / 112

Preparation prior to use

4.7

●

Before the test

(1) Before starting the operation, carefully read in the article 2.2

Cautions for handling

and turn ON the

POWER

switch.

(2) After powering ON of the

POWER

switch, the lamp test of the display is done.

The content to be displayed after the lamp test depends upon the test conditions before
the tester is shutdown.

○

When the power on zero volt slider is set to ON, the slider display shows 0.00kV.

○

When the power on zero volt slider is set to OFF, the slider display shows the set

value of the slider voltage.

○

When the power on zero volt slider is set to OFF and the set value of the slider

voltage is also set to OFF, the slider voltage does not move up or down, and it
displays the slider voltage converting into the test voltage.

4.7.1 Power on zero volt slider function

Select the status of slider voltage for the withstanding voltage test at powering on.

CAUTION

Prior to the start of test, confirm the slider display value.

Setting procedure To enter setting mode of power on zero volt slider

①

Keep pressing the

DOWN

key, turn ON the power.

②

The tester enters the lamp test status. The lamp test for the

DANGER

lamp is for

about 3 seconds.

Then the slider display is lit up with

The operator may leave the

DOWN

key at this moment.

Change of setting

With this status,

can be selected every time the

DOWN

key is pressed.

Finish

Turn the power OFF.

To validate the changed setting

By re-applying the power, the new setting is validated.

ｋＶ

Ｗ／ＩＡＵＴＯＴＥＳＴＥＲＭＯＤＥＬ８５２７

MAX 5kV

OUTPUT

SHIFT

ENTER

ON/OFF

READY

REMOTE

DISCHARGE

KEY LOCK

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

W-TEST

MEMORY

SET

No.

I-TEST

I-W

W-I

LOW

HIGH

GOOD

LOW

HIGH

GOOD

LOW

HIGH

BUZZER

READ

WRITE

LOCK

EXIT

STOP

START

POWER

REMOTE

HIGH VOLTAGE

DOWN

ONLINE

MOTOR BUSY

VOLTAGE SLIDER

LOW

DANGER

Summary of Contents for 8527

















































































































Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands

Tsuruga 8527, Instruction Manual

Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands