Tsuruga 8527 Instruction Manual Download Page 31

Page: 31 / 112

Setting of test condition for insulation resistance test

9.2

●

High limit of resistance value

Adjustable range: 0.2M

~2000M

, OFF

Note-1

: The adjustable range is 0.2~9.9M

(resolution 0.1M

) and 10~2000M

(resolution 1M

Note-2

: The high limit of resistance value can not be lower than that of low limit, so

please apply either corrective solution below:

1. When the low limit value is determined, set the high limit value to exceed the

value of low limit, or turn OFF the setting.

2. When the high limit value is determined, set the low limit value not to exceed

the value of high limit.

Note-3

: When the setting is turned OFF, no judgement for the high limit is made.

When the setting is restored from OFF, and when the high limit value is lower
than the low limit value, the high limit value of resistance is replaced with
2000M

[When turning OFF the setting of high limit of resistance value]

To enter setting mode

①

In READY status, press

key, then the test mode lamp blinks.

Test mode lamp moves up and down with

▲

▼

key. Make the required test

mode lamp blinking (

W-I

I-W

lamp).

②

Press

key and make the test mode lamp lit.

To turn OFF the setting of high limit of resistance value

①

Press

key and select the status that the current/resistance display blinks,

the

is lit up and the

HIGH SET

is also lit.

②

Next, press

ON/OFF

key and select the status that the display blinks with

(refer to the above figure).

To move to the previous setting

Press

key, then changes to the

setting of test range of insulation resistance test

To the next setting

Press

key, then changes to the

setting of low limit of resistance value

Finish of setting

Press

ENTER

key, then the tester returns to READY status, memorizing the set having

been made.
The slider moves up or down when the test mode is W-I or I-W.
When the

EXIT

key (

SHIFT

and

ENTER

at a time) is pressed in the setting mode,

the setting mode for the test condition is interrupted and the tester becomes READY
status.

The test conditions in this case are those before entering the setting mode of test condition.

ON/OFF

ENTER

WRITE

READ

LOCK

○

BUZZER

READY

REMOTE

DISCHARGE

KEY LOCK

EXIT

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

SHIFT

LOW

GOOD

HIGH

LOW

GOOD

HIGH

LOW

○

W-TEST

○

MEMORY

SET

No.

○

I-TEST

I-W

W-I

HIGH

○
●

○

●

VOLTAGE SLIDER

Summary of Contents for 8527

















































































































Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands

Tsuruga 8527, Instruction Manual

Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands