Tsuruga 8527 Instruction Manual Download Page 8

Page: 8 / 112

3. Name of parts and functions

3.1

●

Front panel

①

POWER

Power supply switch. Press right to turn ON and left to turn OFF.

②

STOP

Switch to interrupt the test operation, to reset a judgement and to stop the
slider.

③

START

Switch to start the test.
This switch is disabled when the

REMOTE

connector

⑧

is used, or the

remote operation is made through the

REMOTE

terminal blocks

the

REMOTE/OUT

connector

VOLTAGE SLIDER (for withstanding voltage test)

④

DOWN

Knob to adjust the test voltage of withstanding voltage test.

It is disabled when the key lock function is turned ON.

⑤

Slider display

Displays the slider voltage converting it into the test voltage.

⑥

MOTOR BUSY

lamp

Lit up when the slider is in operation.

⑦

ONLINE

lamp

Lit up when the remote controlled by RS-232C interface.

(For details, refer to the instruction manual of RS-232C interface.)

⑧

REMOTE

Connector for remote control.

⑨

HIGH VOLTAGE

High voltage side terminal of the test voltage output.

It outputs high voltage during the test, so never touch it during the

DANGER

lamp

⑬

is lit up. The operator may suffer electric shock.

It is common with

HIGH VOLTAGE

on the back panel.

⑩

LOW

Low voltage side terminal of the test voltage output. It is of the same
voltage as the case of this tester.

⑪

Output voltmeter

Electrical instrument to indicate the output voltage value.

⑫

Zero adjuster

Knob to adjust the zero position of the voltmeter for withstanding voltage

tester. The adjustment is done when no power is applied.

ｋＶ

DOWN

ｋＶ

DOWN

ONLINE

MOTOR BUSY

Ｗ／ＩＡＵＴＯＴＥＳＴＥＲＭＯＤＥＬ８５２７

VOLTAGE SLIDER

BUZZER

ｍＡ

LOW

H IGH VOLT AGE

REMOTE

STOP

START

POWER

READ

WR IT E

LOCK

EX IT

MAX 5kV

OUTPUT

ＡＣＴＥＳＴＶＯＬＴＡＧＥ

ＣＵＲＲＥＮＴ／ＲＥＳＩＳＴＡＮＣＥ

ＴＩＭＥ

ＲＡＮＧＥ

ＭＯＤＥ

ＭＥＭＯＲＹ

ＪＵＤＧＥ

ＤＩＳＣＨＡＲＧＥ

Ｍ

Ｎｏ．

ｋＶ

ＡＣ

ＤＣ

Ｉ

Ｉ－ＴＥＳＴ

Ｗ

Ｉ

Ｗ－Ｉ

Ｉ－Ｗ

ＨＩＧＨＳＥＴ

ＭΩ

ＬＯＷＳＥＴ

ＫＥＹＬＯＣＫ

ＲＥＭＯＴＥ

ＲＥＡＤＹ

Ｗ－ＴＥＳＴ

ＧＯＯＤ

ＨＩＧＨ

ＬＯＷ

DANGER

SHIFT

ENTER

ON/OFF

Summary of Contents for 8527

















































































































Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands

Tsuruga 8527, Instruction Manual

Search results

Summary of Contents for 8527

Reviews:

Brands by name

Popular brands