manualshive.com logo in svg

Tsuruga 8527, Instruction Manual

Share
Download
Tsuruga 8527 Instruction Manual Download Page 25

 

25 

Setting of test condition for withstanding voltage test 

 

 

8.3 

●

High limit of leak current 

 
 

Adjustable range: 0.1~110.0mA. 

 

Note

:  The high limit value of leak current can not be lower than that of low limit, so 

please apply either corrective solution below: 

 

 

1. When the low limit value is determined, set the high limit value to exceed the 

value of low limit. 

 

 

2. When the high limit value is determined, set the low limit value not to exceed 

the value of high limit, or turn OFF the low limit. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

  To enter setting mode   

 

①

  In READY status, press 

 

 

  or 

 

 

  key, then the test mode lamp blinks.     

 

 

Test mode lamp moves up and down with 

 

▲

 

  or 

 

▼

 

  key.    Make the required test 

mode lamp blinking (

W-I

, 

I-W

 or 

W

 lamp). 

 

②

  Press 

 

 

  or 

 

 

  key and make the test mode lamp lit. 

 
 

  Setting of high limit of leak current   

 

①

  Press 

 

 

  or 

 

 

  key and select the status that the current/resistance display blinks, 

the 

  mA 

  is lit up and the 

  HIGH SET

 is also lit (refer to the above figure). 

 

②

  Press 

 

▲

 

  or 

 

▼

 

  key and set the high limit of leak current value. 

 

③

  Pressing of 

 

 

  key (

 SHIFT 

 

and 

 

▲

 

  at a time) or 

 

 

  key (

 SHIFT 

  and 

 

▼

   

 

      at a time) allows the setting of second digit. 

 
 

  To move to the previous setting   

 

Press 

 

 

 

key, then the setting changes to the 

setting of referential voltage

. 

 
 

  To the next setting   

 

Press 

 

 

  key, then changes to the 

setting of low limit of leak current

. 

 
 

  Finish of setting   

Press 

  ENTER 

  key, then the slider moves up or down and the tester returns to READY 

status, memorizing the set having been made. 
When the 

  EXIT 

  key (

 SHIFT 

  and 

  ENTER 

  at a time) is pressed in the setting mode, 

the setting mode for the test condition is interrupted and the tester becomes READY 
status. 

 

The test conditions in this case are those before entering the setting mode of test condition. 

 
 

ON/OFF

ENTER

WRITE

READ

LOCK

○

○

BUZZER

W

READY

REMOTE

DISCHARGE

KEY LOCK

EXIT

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

SHIFT

M

Ω

LOW

GOOD

HIGH

LOW

GOOD

HIGH

LOW

○

W-TEST

○

○

○

○

○

DC

AC

W

M

MEMORY

SET

SET

kV

s

kV

No.

○

○

○

I

I-TEST

I

I-W

W-I

mA

HIGH

●

●

VOLTAGE SLIDER

 

Summary of Contents for 8527

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands