Toyota Matrix 2003 Operating Manual Download Page 63 | Manualshive

Page: 63 / 306

background image

’03 MATRIX_U (L/O 0201)

63

2003 MY COROLLA MATRIX_U (OM12767U)

4. To remove the convertible seat, press

the buckle–release button and allow the
belt to retract completely. The belt will
move freely again and be ready to
work for an adult or older child passen-
ger.

(C) BOOSTER SEAT INSTALLATION

A booster seat is used in forward–fac-
ing position only.

Move seat
fully back

CAUTION

A forward–facing child restraint sys-
tem should be allowed to be
installed on the front passenger
seat only when it is unavoidable.
Always move the seat as far back
as possible, because the force of
the deploying front passenger air-
bag could cause death or serious
injury to the child.

«
...
61
62
63
64
65
...
»

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

Brand: Jeda Pages: 8

Brand: Jeep Pages: 496

Brand: Alpine Pages: 8

Brand: V8 equipment Pages: 17

1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28

Brand: Havis-Shields Pages: 3

Brand: Buick Pages: 20

Brand: Elinchrom Pages: 101

Brand: MAcarbon Pages: 3

Brand: Black+Decker Pages: 21

Brand: Beeper Pages: 20

Brand: Mercedes-Benz Pages: 493

Brand: SuperATV Pages: 2

Brand: LaserLine Pages: 4

Brand: SAAS Pages: 3

Brand: Nuna Pages: 29

Brand: SkyRack Pages: 2

Brand: Kia Pages: 673

Brand: Prime Design Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands