manualshive.com logo in svg

Toyota Matrix 2003, Operating Manual

The Toyota Matrix 2003 Owner's Manual is a comprehensive guide that provides essential information for owners. Easily download this manual for free from manualshive.com to gain valuable insights on maintenance, troubleshooting, and operating instructions. Experience the convenience of accessing this indispensable resource for your Toyota Matrix 2003.

Share
Download
background image

’03 MATRIX_U (L/O 0201)

97

2003 MY COROLLA MATRIX_U (OM12767U)

Shift into the “L” position. The trans-
mission will downshift to first gear
when the vehicle speed drops down to
or lower than the following speed, and
maximum engine braking will be en-
abled.

Two–wheel drive models

49 km/h (30 mph)

Four–wheel drive models

48 km/h (29 mph)

Vehicles with cruise control—When the
cruise control is being used, even if you
downshift the transmission by pushing and
releasing the overdrive switch, engine
braking will not be enabled because the
cruise control is not cancelled.

For ways to decrease the vehicle speed,
see “Cruise control” on page 101 in this
section.

CAUTION

Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.

(e) Using “2” and “L” positions

The “2” and “L” positions are used for
strong engine braking as described pre-
viously.

With the selector lever in “2” or “L”, you
can start the vehicle in motion as with the
lever in “D”.

With the selector lever in “2”, the vehicle
will start in first gear and automatically
shift to second gear.

With the selector lever in “L”, the trans-
mission is engaged in first gear.

NOTICE

Be careful not to over–rev the en-
gine. Watch the tachometer to keep
engine rpm from going into the red
zone. The approximate maximum al-
lowable speed for each position is
given below for your reference:

1ZZ–FE engine

“2”

110 km/h (68 mph)

. . . . . . . . . 

“L”

60 km/h (37 mph)

. . . . . . . . . . 

2ZZ–GE engine

“2”

120 km/h (74 mph)

. . . . . . . . . 

“L”

67 km/h (41 mph)

. . . . . . . . . . 

Do not continue hill climbing or
hard towing for a long time in the
“2” or “L” position. This may cause
severe automatic transmission dam-
age from overheating. To prevent
such damage, “D” position should
be used in hill climbing or hard
towing.

(f) Backing up

1. Bring the vehicle to a complete stop.

2. With the brake pedal held down with

your foot, shift the selector lever to the
“R” position.

NOTICE

Never shift into reverse while the ve-
hicle is moving.

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Brand: Bimmer Jakes Pages: 4
SnapPad EQ Round Installation Instructions preview
EQ Round
Brand: SnapPad Pages: 5
RAM Ram Dodge 2010 Owner'S Manual preview
Ram Dodge 2010
Brand: RAM Pages: 616
Nav TV AUDI-P60H Install Manual preview
AUDI-P60H
Brand: Nav TV Pages: 9
Honda Clarity 2018 Owner'S Manual preview
Clarity 2018
Brand: Honda Pages: 81
Jaeger J05252127 Fitting Instructions Manual preview
J05252127
Brand: Jaeger Pages: 17
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Brand: Oldsmobile Pages: 380
Horn Tools HJIMRR02FIT Mounting Instructions preview
HJIMRR02FIT
Brand: Horn Tools Pages: 12
Lincoln NAUTILUS 2022 Owner'S Manual preview
NAUTILUS 2022
Brand: Lincoln Pages: 586
Alfa Romeo Giulietta 2.0 JTDM Manual preview
Giulietta 2.0 JTDM
Brand: Alfa Romeo Pages: 14
r.LiNK RL2-MMI3G-Q3 Manual preview
RL2-MMI3G-Q3
Brand: r.LiNK Pages: 21
Toyota Tundra guide Manual preview
Tundra guide
Brand: Toyota Pages: 672
AUTOTECH 10.109.418K Installation Instructions preview
10.109.418K
Brand: AUTOTECH Pages: 4
Xforce PR-104 User Manual preview
PR-104
Brand: Xforce Pages: 11
Tesla Gen 3 Manual preview
Gen 3
Brand: Tesla Pages: 42
Alfa Romeo Stelvio 2019 User Manual preview
Stelvio 2019
Brand: Alfa Romeo Pages: 268
Nav TV NTV-KIT956 Manual preview
NTV-KIT956
Brand: Nav TV Pages: 8
U.S. General 95187 Instruction Sheet preview
95187
Brand: U.S. General Pages: 3

Brands by name

Popular brands

Load more brands