Toyota Matrix 2003 Operating Manual Download Page 58 | Manualshive

Page: 58 / 306

background image

’03 MATRIX_U (L/O 0201)

58

2003 MY COROLLA MATRIX_U (OM12767U)

CAUTION

After inserting the tab, make sure
that the tab and buckle are locked,
and that the lap and shoulder por-
tions of the belt are not twisted.

Do not insert coins, clips, etc. in
the buckle as this may prevent you
from properly latching the tab and
buckle.

If the seat belt does not function
normally, it cannot protect your
child from injury. Contact your
Toyota dealer immediately. Do not
use the child restraint system until
the seat belt is fixed.

2. Fully extend the shoulder belt to put it

in the lock mode. When the belt is
then retracted even slightly, it cannot
be extended.

To hold the infant seat securely, make
sure the belt is in the lock mode before
letting the belt retract.

3. While pressing the infant seat firmly

against the seat cushion and seatback,
let the shoulder belt retract as far as
it will go to hold the infant seat secure-
ly.

«
...
56
57
58
59
60
...
»

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

Brand: Jeep Pages: 12

Brand: Jeep Pages: 6

Brand: Fabbri Pages: 4

Brand: Actia Pages: 37

Brand: Harbor Freight Tools Pages: 12

Brand: Honda Pages: 3

Brand: Gator Pages: 2

Brand: Metra Electronics Pages: 8

DELTA DL FIX 209FP

Brand: Menabo Pages: 8

Brand: BMW Pages: 189

Brand: Pacbrake Pages: 6

Brand: Guidosimplex Pages: 8

Brand: Honda Pages: 124

Jumpy Miltispace

Brand: CITROËN Pages: 164

Brand: Directed Pages: 30

Automobille 2004 Century

Brand: Buick Pages: 12

Brand: ECS Electronics Pages: 14

Brand: NavLinkz Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands