manualshive.com logo in svg

Toyota Matrix 2003, Operating Manual

The Toyota Matrix 2003 Owner's Manual is a comprehensive guide that provides essential information for owners. Easily download this manual for free from manualshive.com to gain valuable insights on maintenance, troubleshooting, and operating instructions. Experience the convenience of accessing this indispensable resource for your Toyota Matrix 2003.

Share
Download
background image

’03 MATRIX_U (L/O 0201)

55

2003 MY COROLLA MATRIX_U (OM12767U)

CAUTION

Never install a rear–facing child re-
straint system on the front seat. In
the event of an accident, the force
of the rapid inflation of the airbag
can cause death or serious injury if
a rear–facing child restraint system
is installed on the front seat.

Unless it is unavoidable, do not
install a forward–facing child re-
straint system on the front seat.

A forward–facing child restraint sys-
tem should be allowed to be
installed on the front passenger
seat only when it is unavoidable.
Always move the seat as far back
as possible, because the force of
the deploying front passenger air-
bag could cause death or serious
injury to the child.

On vehicles with side airbags, do
not allow the child to lean against
the front door or around the front
door even if the child is seated in
the child restraint system. It is dan-
gerous if the side airbags inflate,
because the impact could cause
death or serious injury to the child.

After installing the child restraint
system, make sure it is secured in
place following the manufacturer’s
instructions. If it is not restrained
securely, it may cause death or se-
rious injury to the child in the
event of a sudden stop or accident.

When not using the child restraint system,
keep it secured with the seat belt or place
it somewhere other than the passenger
compartment. This will prevent it from in-
juring passengers in the event of a sud-
den stop or accident.

Child restraint systems are classified into
the following 3 types depending on the
child’s age and size.

(A) Infant seat
(B) Convertible seat
(C) Booster seat

Install the child restraint system following
the instructions provided by its manufac-
turer.

Your vehicle has anchor brackets for se-
curing the top strap of a child restraint
system.

For instructions about how to use the an-
chor bracket, see “—Using a top strap” on
page 65 in this section.

The child restraint lower anchorages ap-
proved for your vehicle may also be used.
See “—Installation with child restraint low-
er anchorages” on page 67 in this section.

—Types of child restraint
system

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

Jabra TOUR Get Started preview
TOUR
Brand: Jabra Pages: 10
Carcomm CNM-71 Quick Start Manual preview
CNM-71
Brand: Carcomm Pages: 2
Whispbar K392W Fitting Instructions For Basic Carrier preview
K392W
Brand: Whispbar Pages: 14
GMC SIERRA 2002 Manual preview
SIERRA 2002
Brand: GMC Pages: 499
Kia Amanti Owner'S Manual preview
Amanti
Brand: Kia Pages: 290
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Brand: Haibang Pages: 6
BGS technic 40108 Manual preview
40108
Brand: BGS technic Pages: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Brand: Oldsmobile Pages: 344
ABL eMH3 Installation Manual preview
eMH3
Brand: ABL Pages: 66
Atera 022 681 Manual preview
022 681
Brand: Atera Pages: 10
RAM 4500 CHASSIS CAB 2012 Specification preview
4500 CHASSIS CAB 2012
Brand: RAM Pages: 7
BURY CC 9040 Specification preview
CC 9040
Brand: BURY Pages: 2
Whispbar K919W Fitting Instructions Manual preview
K919W
Brand: Whispbar Pages: 17
mtf TRANSPORT SYSTEM BackPower Manual preview
BackPower
Brand: mtf TRANSPORT SYSTEM Pages: 9
T-Mobile SyncUP DRIVE Start Manual preview
SyncUP DRIVE
Brand: T-Mobile Pages: 2
Yakima K1249 Instructions Manual preview
K1249
Brand: Yakima Pages: 9
BMW M3 SEDAN Owner'S Manual preview
M3 SEDAN
Brand: BMW Pages: 392
Curt Manufacturing 13434 Installation Instructions preview
13434
Brand: Curt Manufacturing Pages: 4

Brands by name

Popular brands

Load more brands