manualshive.com logo in svg

Toyota Matrix 2003, Operating Manual

The Toyota Matrix 2003 Owner's Manual is a comprehensive guide that provides essential information for owners. Easily download this manual for free from manualshive.com to gain valuable insights on maintenance, troubleshooting, and operating instructions. Experience the convenience of accessing this indispensable resource for your Toyota Matrix 2003.

Share
Download
background image

You are responsible for performance of the required maintenance indi-
cated in the 

Owner’s Manual

and the 

Scheduled Maintenance Guide

.

Toyota recommends that you retain all receipts covering maintenance on
your vehicle, but Toyota cannot deny warranty coverage solely for the
lack of receipts or your failure to ensure the performance of all scheduled
maintenance.

You are responsible for presenting your vehicle to a Toyota dealership as
soon as a problem exists. The warranty repairs should be completed in a
reasonable amount of time, not to exceed 30 days.

You should also be aware that Toyota may deny you warranty coverage if
your vehicle or a part has failed due to abuse, neglect, improper main-
tenance or unapproved modifications.

If you have any questions regarding your warranty rights and responsi-
bilities, you should contact the Toyota Customer Assistance Center at
(800)331-4331 or the California Air Resources Board, Mobile Source
Control Division, at 9528 Telstar Avenue, P.O. Box 8001, El Monte, CA
91734-8001.

These warranty obligations do not apply to failures or noncompliance
caused by:

•

The use of replacement parts not certified in accordance with 
aftermarket parts certification regulations.

•

The use of replacement parts not equivalent in quality or design to
original equipment parts.

Provisions under the “What Is Not Covered” section of the New Vehicle
Limited Warranty also apply to this warranty.

OWNER’S WARRANTY RESPONSIBILITIES

WHAT IS NOT COVERED

Your Warranties in Detail

21

California Emission Control Warranty

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

Kolpin 25-9250 Owner'S And Operator'S Manual preview
25-9250
Brand: Kolpin Pages: 25
CITROEN PICASSO XSARA DESIRE 1.6 - MESUREMENT Manual preview
PICASSO XSARA DESIRE 1.6 - MESUREMENT
Brand: CITROEN Pages: 2
John Gold Gold Cruuse Cruisecontrol GC90 Installation Manual preview
Gold Cruuse Cruisecontrol GC90
Brand: John Gold Pages: 24
Whispbar K498W Fitting Instructions Manual preview
K498W
Brand: Whispbar Pages: 14
Phonocar VM338 Mounting Instructions preview
VM338
Brand: Phonocar Pages: 6
Havis-Shields 1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28 Install Instructions preview
1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28
Brand: Havis-Shields Pages: 3
Safe Fleet RVS systems RVS-M641 Instruction Manual preview
RVS systems RVS-M641
Brand: Safe Fleet Pages: 24
PUTCO Molle Panels Assembly And Instruction Manual preview
Molle Panels
Brand: PUTCO Pages: 2
NavLinkz RL4-ELINK Manual preview
RL4-ELINK
Brand: NavLinkz Pages: 23
Jeep Grand Cherokee SRT 2019 Owner'S Manual preview
Grand Cherokee SRT 2019
Brand: Jeep Pages: 656
Honda 08B15-SDN-100 Installation Instructions Manual preview
08B15-SDN-100
Brand: Honda Pages: 22
Mercedes-Benz 2013 CL Operator'S Manual preview
2013 CL
Brand: Mercedes-Benz Pages: 494
Voxx Electronics CA-510a Installation Instructions Manual preview
CA-510a
Brand: Voxx Electronics Pages: 15
Roadmaster 195125 Assembly And Operating Instructions preview
195125
Brand: Roadmaster Pages: 4
Gacell SLH 27C User Manual preview
SLH 27C
Brand: Gacell Pages: 25
JBA 1528S Installation Instructions And Warranty Information preview
1528S
Brand: JBA Pages: 5
Uniden BTSC1100 Owner'S Manual preview
BTSC1100
Brand: Uniden Pages: 16
Chrysler Sebring Convertible Owner'S Manual preview
Sebring Convertible
Brand: Chrysler Pages: 454

Brands by name

Popular brands

Load more brands