manualshive.com logo in svg

Toyota Matrix 2003, Operating Manual

The Toyota Matrix 2003 Owner's Manual is a comprehensive guide that provides essential information for owners. Easily download this manual for free from manualshive.com to gain valuable insights on maintenance, troubleshooting, and operating instructions. Experience the convenience of accessing this indispensable resource for your Toyota Matrix 2003.

Share
Download
background image

’03 MATRIX_U (L/O 0201)

249

2003 MY COROLLA MATRIX_U (OM12767U)

Even if the damage does not appear seri-
ous, a qualified technician should examine
the damage. Objects which have pene-
trated the tire may have caused internal
damage.

Any tires which are over 6 years old
must be checked by a qualified techni-
cian even if damage is not obvious.

Tires deteriorate with age even if they
have never or seldom been used.

This also applies to the spare tire and
tires stored for future use.

REPLACING YOUR TIRES

Two–wheel drive models—When replac-
ing a tire, use only the same size and
construction as originally installed and
with the same or greater  load capacity.

Four–wheel drive models—When replac-
ing tires, make sure all the tires are the
same brand. Only use the same size,
construction and tread patterns as the
originally installed tires, with the same
or greater load capacity.

Using any other size or type of tire may
seriously affect handling, ride, speedome-
ter/odometer calibration, ground clearance,
and clearance between the body and tires
or snow chains.

CAUTION

Do not mix radial, bias belted, or
bias–ply tires on your vehicle. It
can cause dangerous handling char-
acteristics, resulting in loss of con-
trol.

Do not use tire or wheels other
than the manufacturer’s recom-
mended size.

Toyota recommends all four tires, or at
least both front or rear tires be re-
placed as a set.

See “If you have a flat tire” on page 202
in Section 4 for tire change procedure.

When a tire is replaced, the wheel
should always be balanced.

An unbalanced wheel may affect vehicle
handling and tire life. Wheels can get out
of balance with regular use and should
therefore be balanced occasionally.

When replacing a tubeless tire, the air
valve should also be replaced with a
new one.

To equalize tire wear and help extend
tire life, Toyota recommends that you
rotate your tires according to the main-
tenance schedule. (For scheduled main-
tenance information, please refer to the
“Scheduled Maintenance Guide” or
“Owner’s Manual Supplement”.) Howev-
er, the most appropriate timing for tire
rotation may vary according to your
driving habits and road surface condi-
tions.

See “If you have a flat tire” on page 202
in Section 4 for tire change procedure.

—Rotating tires

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

Lancia Y Owner'S Handbook Manual preview
Y
Brand: Lancia Pages: 191
Jeep Compass Owner'S Handbook Manual preview
Compass
Brand: Jeep Pages: 322
Jeep Compass Repair Manual preview
Compass
Brand: Jeep Pages: 341
Jeep Compass Operating Information Manual preview
Compass
Brand: Jeep Pages: 310
Jeep Compass Information Manual preview
Compass
Brand: Jeep Pages: 189
Jeep Compass Review preview
Compass
Brand: Jeep Pages: 26
Jeep Compass Overview preview
Compass
Brand: Jeep Pages: 21
Conrad 75 16 30 Operating Instructions Manual preview
75 16 30
Brand: Conrad Pages: 26
Ford 2003 Thunderbird Owner'S Manual preview
2003 Thunderbird
Brand: Ford Pages: 200
BESAFE iZi Flex Manual preview
iZi Flex
Brand: BESAFE Pages: 4
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Brand: hc-cargo Pages: 60
EZTRUNK PHANTOM JK Assembly Manual preview
PHANTOM JK
Brand: EZTRUNK Pages: 3
Zap XEBRA ZAPCAR Series Owner'S Manual preview
XEBRA ZAPCAR Series
Brand: Zap Pages: 16
Gator GRM430EM User Manual preview
GRM430EM
Brand: Gator Pages: 6
rough country 921107830 Installation Instruction preview
921107830
Brand: rough country Pages: 4
Ford FUSION 2014 Owner'S Manual preview
FUSION 2014
Brand: Ford Pages: 458
Yakima K896 Instructions Manual preview
K896
Brand: Yakima Pages: 12
Pyle PLPSC8 User Manual preview
PLPSC8
Brand: Pyle Pages: 14

Brands by name

Popular brands

Load more brands