Toyota Matrix 2003 Operating Manual Download Page 45 | Manualshive

Page: 45 / 306

background image

’03 MATRIX_U (L/O 0201)

45

2003 MY COROLLA MATRIX_U (OM12767U)

Move seat
fully back

A forward–facing child restraint sys-
tem should be allowed to be
installed on the front passenger
seat only when it is unavoidable.
Always move the seat as far back
as possible, because the force of
the deploying front passenger air-
bag could cause death or serious
injury to the child.

On vehicles with side airbags, do
not allow the child to lean against
the front door or around the front
door even if the child is seated in
the child restraint system. It is dan-
gerous if the side airbags inflate,
because the impact could cause
death or serious injury to the child.

For instructions concerning the
installation of a child restraint sys-
tem, see “Child restraint” on page
53 in this section.

Do not sit on the edge of the seat
or lean over the dashboard when
the vehicle is in use, since the
front airbags inflate with consider-
able speed and force. Otherwise,
you may be killed or seriously in-
jured. Sit up straight and well back
in the seat, and always use your
seat belt properly.

«
...
43
44
45
46
47
...
»

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: Acdeos Pages: 38

Brand: Kargo Master Pages: 6

Brand: Oldsmobile Pages: 360

Brand: Aries Pages: 3

Brand: Axxess Pages: 4

Brand: Vintage Air Pages: 14

Sterling ALL-TERRAIN 576

Brand: Roadmaster Pages: 12

Brand: Acura Pages: 2

Brand: Whispbar Pages: 15

v.LOGiC Intelligent Solution V5-NTG46

Brand: Caraudio-Systems Pages: 18

Brand: ULTIMATE SPEED Pages: 21

Brand: Tachosys Pages: 28

Airgo Active cushion / Comfort

Brand: TOGU Pages: 2

Brand: Ford Pages: 256

Civic Hatch 2017

Brand: Honda Pages: 687

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands