Toyota Matrix 2003 Operating Manual Download Page 207 | Manualshive

Page: 207 / 306

background image

’03 MATRIX_U (L/O 0201)

207

2003 MY COROLLA MATRIX_U (OM12767U)

Jack point guide

With side mud guards—The jack point
guides are located under the side mud
guards. They indicate the jack point posi-
tions.

6. After making sure that no one is in

the vehicle, raise it high enough so
that the spare tire can be installed.

Remember you will need more ground
clearance when putting on the spare tire
than when removing the flat tire.

To raise the vehicle, insert the jack handle
into the jack (it is a loose fit) and turn it
clockwise. As the jack touches the vehicle
and begins to lift, double–check that it is
properly positioned.

CAUTION

Never get under the vehicle when the
vehicle is supported by the jack
alone.

—Raising your vehicle

«
...
205
206
207
208
209
...
»

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

Brand: Jetter Pages: 4

Brand: K&K Pages: 8

Brand: K&K Pages: 20

Brand: K&K Pages: 6

Brand: K&K Pages: 3

Brand: K&K Pages: 3

Brand: Jeep Pages: 12

Brand: Jeep Pages: 6

Brand: Hama Pages: 75

Brand: AutoWatch Pages: 4

Brand: Mercedes-Benz Pages: 368

Brand: Fab Fours Pages: 21

2005 JR41 Stratus

Brand: Dodge Pages: 293

Alloy Rugged Ridge X-Clamp

Brand: Omix-Ada Pages: 2

Brand: Dodge Pages: 3

Brand: GReddy Pages: 12

Brand: Needit Pages: 2

KIT ParkingSensor 814

Brand: Gemini Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands